ПН,- ПТ, 10:00 - 18:00

620026 г. Екатеринбург, ул. Куйбышева, д.48Б

sales@kyomart.ru

8 (343) 288-23-45

Контакты

Каталог

Коды ошибок Kyocera FS-1025


Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.
В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов. Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.
Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону +7 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.

Код ошибки Описание ошибки Причина ошибки
0030 FAX Board System Error Cannot communicate with the modem when activated. Defective FAX PWB.
0100 Backup memory read/write error(NOR) Flash returns an abnormal status. Defective flash memory. Defective main PWB..
0120 MAC address data error For data in which the MAC address is invalid. Defective flash memory. Defective engine PWB.
0190 Backup memory error (engine) Unable to read the main PWB IC. Defective flash memory. Defective main PWB.
0630 Scan DMA error Unable to transfer DMA. Defective main PWB.
2000 Main motor error Pulse is not detected after 1000msec. Motor won’t stabilize after 300msec. Defective connector cable or poor contact in the connector Defective drive transmission system of motor. Defective motor. Defective main PWB.
3100 Scanner Carriage Error The HP sensor won't be opened when it is driven in the scan direction for 37.44 mm (*1) at the initial scanning when the HP sensor is cut off. The HP sensor won't be cut off when it is driven in the return direction for 320.44mm (*2) at the initial scanning when the HP sensor is open. Defective connector cable or poor contact in the connector. Defective home position sensor. Defective scanner motor. Defective main PWB.
3300 AGC Error The resultant AGC fell outside the range of allowance. Defective connector cable or poor contact in the connector. CIS sensor. Defective main PWB.
3500 Scan ASIC Error The scan ASIC has been inoperative. Defective main PWB.
4000 Polygon motor synchronize error Polygon motor is not stabilized within 15 s since the motor is activated. After polygon motor is stabilized, the ready signal is not detected for 7 s continuously. Defective connector cable or poor contact in the connector. Defective polygon motor. Defective main PWB.
4200 BD stability error The BD signal is not detected for 1000 ms after processing the compulsion lighting. At the interrupt in VSYNC, the BD error is detected continuously for 10 times in 400 ms intervals. Defective connector cable or poor contact in the connector. Defective APC PWB. Defective main PWB.
6000 Broken fuser heater The temperature does not reach 100° C/212 °F after the fuser heater lamp has been turned on continuously for 30 s. At the time of 20 degrees or less from specified temperature, the fuser temperature does not rise by 2 degrees or more after the fuser heater lamp has been turned on continuously for 8 s.(during ready or during print) Defective connector cable or poor contact in the connector. Fuser thermostat triggered. Defective fuser heater. Defective main PWB.
6020 Abnormally high fuser thermistor temperature Fuser thermistor detects a temperature higher than 210°C/410°F for 3 s Shorted fuser thermistor. Defective control PWB.
6030 Broken fuser thermistor wire Average input AD given by the thermistor is less than 2 for 300msec. Defective connector cable or poor contact in the connector. Broken fuser thermistor wire. Fuser thermostat triggered. Defective main PWB.
6400 Fixing control zero cross signal error The ZCROSS signal does not reach the main PWB for more than 2 s. Defective connector cable or poor contact in the connector. Defective power source PWB. Defective main PWB.
F000 Communication Error between Main PCB and Panel PCB Communication failure during the start-up or operation. * : Only 3 in 1 25/26 ppm model, 4 in 1 20/21, 25/26 ppm model Defective main PWB. Defective operation PWB.
F020 RAM R/W error The average AD value of the sensor input is smaller than 2 during SLP_RLY is off and 300 ms. Defective main PWB.
F040 Communication Error between Main PCB and Engine PCB Communication is failed between the controller and the engine. Defective main PWB.
F050 No Engine Main Program Engine program failure. Defective engine software. Defective main PWB.

×

Заказать обратный звонок

55,52,51,49,56,55,49,102,102,102,98,98,54,97,57,54,56,99,54,57,102,52,50,52,102,98,99,53,97,48,101,51
Нажимая на кнопку, вы даете согласие на обработку своих
персональных данных и соглашаетесь с политикой конфиденциальности
Спасибо за оставленную заявку!
Наш оператор свяжется с вами в ближайшее время
Kyomart.ru
Екатеринбург
ул. Куйбышева, 48Б
620026 +7 (343) 288-23-45
sales@kyomart.ru