01 февраля 2018
05 декабря 2016
01 декабря 2016
Коды ошибок Kyocera FS-1040
Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.
В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.
Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.
Код ошибки | Описание ошибки | Причина ошибки |
---|---|---|
0100 | Backup memory read/write error (NOR) Flash returns an abnormal status. | Defective flash memory. |
0120 | MAC address data error For data in which the MAC address is invalid. | Defective flash memory. |
0190 | Backup memory error (engine) Unable to read the main PWB IC. | Defective flash memory. Defective main PWB. |
2000 | Main motor error Pulse is not detected after 1000msec. Motor won’t stabilize after 300msec. | Defective connector cable or poor contact in the connector. Defective drive transmission system of motor. Defective motor. Defective main PWB. |
4000 | Polygon motor synchronize error Polygon motor is not stabilized within 15 s since the motor is activated. After polygon motor is stabilized, the ready signal is not detected for 7 s continuously. | Defective connector cable or poor contact in the connector. Defective polygon motor. Defective main PWB. |
4200 | BD stability error The BD signal is not detected for 1000 ms after processing the compulsion lighting. At the interrupt in VSYNC, the BD error is detected continuously for 10 times in 400 ms intervals. | Defective connector cable or poor contact in the connector. Defective APC PWB. Defective main PWB. |
6000 | Broken fuser heater The temperature does not reach 100° C/212 °F after the fuser heater lamp has been turned on continuously for 30 s. At the time of 20 degrees or less from specified temperature, the fuser temperature does not rise by 2 degrees or more after the fuser heater lamp has been turned on continuously for 8 s.(during ready or during print) | Defective connector cable or poor contact in the connector. Fuser thermostat triggered. Defective fuser heater. Defective main PWB. |
6020 | Abnormally high fuser thermistor temperature Fuser thermistor detects a temperature higher than 210°C/410°F for 3 s | Deformed connector pin. Shorted fuser thermistor. Defective power source PWB. Defective main PWB. |
6030 | Broken fuser thermistor wire Average input AD given by the thermistor is less than 2 for 300msec. | Defective connector cable or poor contact in the connector. Broken fuser thermistor wire. Fuser thermostat triggered. Defective main PWB. |
6400 | Fixing control zerocross signal error The ZCROSS signal does not reach the main PWB for more than 2 s. | Defective connector cable or poor contact in the connector. Defective power source PWB. Defective main PWB. |